Pulnix TS-9720EN Series Manual de Instalação descarregar pdf (Página 113)

Page 101

VIS CAM 300/400 Installation Manual

12 Appendix H: Troubleshooting

TABLE 36. Troubleshooting table.

TABLE 37. Fault symptom TABLE 38. Check/Possible

reason

Flash fires only every second time Switch S3 on VIS CAM I/O Board is in position “FLASH

2” and only one flash is installed to the camera. Set switch

S3 to position “NIGHT L.”

Camera(s) does not trigger Switch S3 and/or S5 is set to the wrong trigger polarity.

Please refer to section 3.3.6 for setting the switches

Laser connected to IO Board connector X7 does not trigger

the camera

Check that switch S3 and/or S5 is set to “positive going”

(pushed towards X1/X2 connector) on the J-Panel

1 2 ... 108 109 110 111 112 113 114 115 116

Vehicle Imaging 1
Subsystem 300/400 1
Warranty 3
Certifications 3
WARNING 4
Table of Contents 5
Page vii 7
Page viii 8
List of Figures 9
List of Tables 11
Page xii 12
1 Introduction 13
FIGURE 1. VIS elements 14
1.3.2 VISCAM 15
1.3.3 Illumination 16
1.3.4 VJP-300 Junction Panel 16
1.3.5 RS485 Device Server 16
1.4 Operational Overview 17
2 Preparing for installation 18
Preparing for installation 21
1. Disconnect Power 27
3.2 Installing the Camera(s) 29
3.3 Installing the J-Panel 33
FIGURE 24. Test trigger 38
3.4 Illumination Options 40
1 2 3 4 5 6 40
1 2 3 4 5 6 7 8 42
4 System Set-Up 43
5.1 I/O Board Layout 56
5.2.1 Functionality 57
FIGURE 40. Interface drawing 58
5.2.6 Typical wiring diagram 61
5.3.1 Functionality 62
FIGURE 46. Switch location 63
TABLE 12. Wiring diagram 63
5.3.5 Typical Wiring Diagram 64
5.3.7 Functionality 65
FIGURE 53. Connecting to a 2 68
FIGURE 56. Detection board 70
5.5.1 Functionality 71
TABLE 14. Connector table 72
5.6.1 Functionality 73
5.6.5 Test setup 1 75
5.6.6 Test setup 2 76
5.7.1 Functionality 77
5.8 Cables 78
6.1 J-Panel Layout 79
Description 81
6.2.5 Typical Wiring diagram 82
6.2.6 Indicators 83
6.2.7 Switches 83
6.3.1 Functionality 84
6.3.2 Connector specification 84
TABLE 20. Signal table 85
6.3.5 Typical Wiring diagram 86
6.3.6 Indicators 87
6.3.7 Switches 87
6.4.1 Functionality 88
6.4.5 Indicators 89
6.7 X6, X7: 24V DC Power 92
FIGURE 76. RS485 to Ethernet 94
6.11 X14: External Trigger 97
FIGURE 81. Trigger 0 98
FIGURE 82. Trigger 1 98
TABLE 32. Connector table 98
6.12.1 Functionality 99
Master to slave connections 103
FIGURE 86. Terminal block 104
Page 100 112
Page 101 113
Page 102 114
www.jai.com 116

Comentários a estes Manuais

Sem comentários

Pulnix TS-9720EN Series Manual de Instalação Página 113

Comentários a estes Manuais

Manuais e produtos relacionados com Câmaras bridge Pulnix TS-9720EN Series