Pulnix TS-9720EN Series Manual de Instalação descarregar pdf (Página 102)

Page 90

VIS CAM 300/400 Installation Manual

Appendix C: Two Cameras, One Flash Configuration

7 Appendix C: Two Cameras, One Flash Configuration

Figure 7.1 shows how to connect one flash to two VIS CAM 300 cameras. The flash output from

camera 0, the master camera, is connected to the laser trigger input on camera 1, the slave camera. The

Flash unit is connected to the slave camera.

The flash output must always be enabled on the master camera. The flash output on the slave camera is

setup as normal (controlled by the values from the light sensor).

FIGURE 85. Two camera, one flash, configuration.

1 2 ... 97 98 99 100 101 102 103 104 105 106 107 ... 115 116

Vehicle Imaging 1
Subsystem 300/400 1
Warranty 3
Certifications 3
WARNING 4
Table of Contents 5
Page vii 7
Page viii 8
List of Figures 9
List of Tables 11
Page xii 12
1 Introduction 13
FIGURE 1. VIS elements 14
1.3.2 VISCAM 15
1.3.3 Illumination 16
1.3.4 VJP-300 Junction Panel 16
1.3.5 RS485 Device Server 16
1.4 Operational Overview 17
2 Preparing for installation 18
Preparing for installation 21
1. Disconnect Power 27
3.2 Installing the Camera(s) 29
3.3 Installing the J-Panel 33
FIGURE 24. Test trigger 38
3.4 Illumination Options 40
1 2 3 4 5 6 40
1 2 3 4 5 6 7 8 42
4 System Set-Up 43
5.1 I/O Board Layout 56
5.2.1 Functionality 57
FIGURE 40. Interface drawing 58
5.2.6 Typical wiring diagram 61
5.3.1 Functionality 62
FIGURE 46. Switch location 63
TABLE 12. Wiring diagram 63
5.3.5 Typical Wiring Diagram 64
5.3.7 Functionality 65
FIGURE 53. Connecting to a 2 68
FIGURE 56. Detection board 70
5.5.1 Functionality 71
TABLE 14. Connector table 72
5.6.1 Functionality 73
5.6.5 Test setup 1 75
5.6.6 Test setup 2 76
5.7.1 Functionality 77
5.8 Cables 78
6.1 J-Panel Layout 79
Description 81
6.2.5 Typical Wiring diagram 82
6.2.6 Indicators 83
6.2.7 Switches 83
6.3.1 Functionality 84
6.3.2 Connector specification 84
TABLE 20. Signal table 85
6.3.5 Typical Wiring diagram 86
6.3.6 Indicators 87
6.3.7 Switches 87
6.4.1 Functionality 88
6.4.5 Indicators 89
6.7 X6, X7: 24V DC Power 92
FIGURE 76. RS485 to Ethernet 94
6.11 X14: External Trigger 97
FIGURE 81. Trigger 0 98
FIGURE 82. Trigger 1 98
TABLE 32. Connector table 98
6.12.1 Functionality 99
Master to slave connections 103
FIGURE 86. Terminal block 104
Page 100 112
Page 101 113
Page 102 114
www.jai.com 116

Comentários a estes Manuais

Sem comentários

Pulnix TS-9720EN Series Manual de Instalação Página 102

Comentários a estes Manuais

Manuais e produtos relacionados com Câmaras bridge Pulnix TS-9720EN Series